Best Office Chairs Europe

Office chair gas lifts: what EN 16955 Class 3 and Class 4 mean, and how to replace one

Replacement gas cylinders are sold by class, and listings rarely say what the class means. The European standard does, in one short table.

Updated By The Best Office Chairs Europe editorial team13 sources

EN 16955:2017 is the European standard for office chair gas lifts. It grades the pressure tube in Classes 2, 3 and 4 by an alternate bending moment of ±190, ±210 and ±240 Nm, applied 2,000,000 times to 32 tubes with no crack allowed. Class 4 is the strongest. Class 1 was dropped, and the standard replaced Germany's DIN 4550 in 2017.

The class tells you how much bending the steel tube under your seat survives, not how much the whole chair carries. The chair's own rating comes from its maker and from EN 1335, the European standard for office work chairs. What follows is from the standard's published pages, one gas-spring maker's datasheet and the documents of the chairs in our register.

EN 16955 gas-lift strength classes 2, 3 and 4Side view of an office chair seat on a gas-lift column, with u marked as the horizontal distance from the column centre to the load-bearing structure of the seat. Beside it, EN 16955:2017 Table 1: Class 2, alternate bending moment ±190 Nm, u up to 340 mm, about 1267 N at a 150 mm lever; Class 3, alternate bending moment ±210 Nm, u up to 370 mm, about 1400 N at a 150 mm lever; Class 4, alternate bending moment ±240 Nm, u up to 400 mm, about 1600 N at a 150 mm lever. Each test runs 2,000,000 cycles on 32 tubes.EN 16955:2017 · STRENGTH CLASSES OF THE GAS-LIFT PRESSURE TUBEuu = largest distance from the column’s centreto the load-bearing structure of the seatpressure tubeholding conespindleBending moment, ±Nm · 2 million cyclesForce at 150 mm lever: our calc.0501001502002502±190u max. 340 mm · 1,267 N3±210u max. 370 mm · 1,400 N4±240u max. 400 mm · 1,600 NCLASSClass 1 is no longer in the standard.32 tubes per test; no crack allowed in any.
EN 16955:2017 Table 1, drawn to scale: the bending moment each class must survive, and u, the largest seat offset it is meant for. Forces at the 150 mm test lever are our calculation.

What do gas lift Classes 2, 3 and 4 mean?

Each class is defined by two numbers. M is the alternate bending moment the pressure tube must survive in the test. u is the largest distance between the load-bearing structure of the seat and the centre of the column: the further the seat reaches out from the column, the more leverage a sitting person has on the tube.

EN 16955:2017 Table 1, strength classes for pressure tubes, with the equivalent test force at the 150 mm lever (force is our calculation: M ÷ 0.15 m)
Strength classBending moment MSeat offset u, max.Force at 150 mmM vs Class 2
Class 2±190 Nm≤ 340 mm≈1,267 N–
Class 3±210 Nm≤ 370 mm≈1,400 N+11%
Class 4±240 Nm≤ 400 mm≈1,600 N+26%

Class 1 is not in the standard: a footnote to Table 1 says it was left out "due to increased requirements". A gas lift sold today as Class 1 is not graded to EN 16955. The step from Class 3 to Class 4 is ±30 Nm, about 14% more bending moment, and 30 mm more seat offset.

How is a gas lift tested to EN 16955?

The standard tests the pressure tube, the steel tube that carries the gas spring, for strength and durability. Clause 6 sets the procedure:

  • Sample: 32 pressure tubes taken at random from series production, marked before the test. Every combination of dimensions, production method, surface finish or material needs its own test.
  • Load: the class's alternate bending moment, applied through a lever of (150 ± 5) mm with a sinusoidal force, to ISO 1099, at no more than 30 Hz and with the tube no warmer than 50 °C.
  • Duration: 2,000,000 cycles at a mean stress of zero.
  • Inspection: a magnetic powder flaw test over the whole length and circumference of every tube.
  • Pass: no cracks or fractures on any of the 32 tubes.

Three things are outside this test. It does not check gas pressure, leaks or how smoothly the seat moves; no user sits in it, since the load is a bending moment on the tube; and it does not test the rest of the chair. Seat, back and base durability belong to EN 1335-2 for office chairs, and the parts a visitor-chair standard leaves out, seat-height mechanisms among them, are listed on our EN 16139 page.

Class 3 or Class 4: which do you need?

The standard's Annex B, "Guide for choosing the correct strength class", picks the class from the user's weight and the dimension u, and its clause B.5 covers gas springs outside its Table B.1. We could read only the clause titles of Annex B, not its table. A gas-spring maker that publishes its own certification, ACP International in Dronten (Netherlands), states that its Class 3 springs are certified for users up to 120 kg and its Class 4 springs for up to 150 kg.

Applied to the 35 gas-lift chairs in our register with a seat-height range, those two thresholds split the published maximum user weights like this:

For the chairs above 150 kg, a generic Class 4 spring is certified below the chair's own rating, going by ACP's 150 kg figure. Replace it with the chair maker's part, which belongs to the chair that was tested at that weight. On every chair, a replacement should be at least the class of the original; a gaming chair listed with a Class 4 gas lift still has its weight rating set by the chair maker: Secretlab gives the same TITAN Evo a 130 kg or 180 kg maximum depending on size, as we show on gaming vs ergonomic chairs. How chair weight ratings are tested is explained in office chairs for heavier people.

What is printed on a gas lift?

Clause 8 requires every pressure tube to be marked indelibly with:

  1. the manufacturer;
  2. the type designation;
  3. a reference to EN 16955;
  4. the strength class.

The marking is applied before testing, so the tested tubes carry it too. A normative Annex A adds product information on the marking of the gas spring, its activation, the connection between pressure tube and seat mechanism, and the holding cone on the mechanism. If there is no class and no "EN 16955" on the tube, the spring was not marked to this standard.

As an example of what a gas-spring datasheet lists, ACP's 2025 sheet for its standard chrome range gives cone size 28, a wall thickness of 1.5 mm on the outer tube and 2.5 mm on the spindle, forces of 320 or 350 N, strokes from 65 to 305 mm, Class 3 with a chrome spindle and Class 4 with a lightly nitrided spindle, and a 6-year guarantee. Those are one supplier's figures, not values from the standard.

What length gas lift do you need?

A replacement needs the same stroke and the same overall length as the original; otherwise the seat no longer reaches the heights the chair was designed for. The stroke is close to the seat-height travel the maker publishes. The 35 gas-lift chairs in our register travel between 90 and 260 mm, median 115 mm.

Seat-height travel (maximum minus minimum seat height, our calculation) and published maximum user weight for 35 register chairs on a gas lift, with the weight band above
ChairSeat height, mmTravel, mmMax. userWeight band
Löffler Figo Air460–55090120 kgup to 120 kg
Löffler Lezgo 72460–55090120 kgup to 120 kg
Steelcase Leap415–515100150 kg121–150 kg
Steelcase Please420–520100–not published
Steelcase Gesture415–518103180 kgabove 150 kg
Interstuhl PUREis3430–535105–not published
Steelcase Karman410–515105160 kgabove 150 kg
IKEA JÄRVFJÄLLET450–560110110 kgup to 120 kg
IKEA MARKUS460–570110110 kgup to 120 kg
Interstuhl JOYCEis3415–525110150 kg121–150 kg
Sedus se:motion420–530110130 kg121–150 kg
Steelcase Amia430–540110160 kgabove 150 kg
Steelcase Series 1410–520110150 kg121–150 kg
Steelcase Series 2400–510110160 kgabove 150 kg
Herman Miller Cosm417–531114159 kgabove 150 kg
Herman Miller Aeron406–521115159 kgabove 150 kg
Herman Miller Embody406–521115136 kg121–150 kg
Herman Miller Mirra 2406–521115159 kgabove 150 kg
Herman Miller Sayl406–521115159 kgabove 150 kg
Dauphin Indeed mesh400–520120150 kg121–150 kg
Haworth Fern420–540120150 kg121–150 kg
Haworth Zody400–520120150 kg121–150 kg
Kinnarps 8000410–530120110 kgup to 120 kg
Sedus se:flex400–520120130 kg121–150 kg
Vitra AC 5 Work400–520120–not published
Vitra ID Mesh400–520120–not published
Wilkhahn IN400–520120–not published
Wilkhahn ON400–520120–not published
RH Logic 400420–541121150 kg121–150 kg
Kinnarps Capella Classic400–530130130 kg121–150 kg
Interstuhl EVERYis1410–545135150 kg121–150 kg
HÅG Futu Mesh 1100400–550150110 kgup to 120 kg
HÅG SoFi Mesh 7500390–540150110 kgup to 120 kg
HÅG Capisco 8106460–640180110 kgup to 120 kg
Varier Move560–820260110 kgup to 120 kg

Several makers also sell different lifts for the same chair, which changes the seat-height range. If you are very short or very tall, a factory lift option is a better fix than an aftermarket spring:

Gas lift options the makers publish for 10 register chairs, with the seat height (mm) each gives
ChairStandard liftOther lifts
HÅG Capisco 8106200 mm lift: 460–640150 mm lift: 400–540; 265 mm lift: 550–810
HÅG Futu Mesh 1100165 mm lift: 400–550200 mm lift: 450–640
HÅG SoFi Mesh 7500165 mm lift: 390–540200 mm lift: 450–640
RH Logic 400standard stem: 420–541optional stems: approx. 490–635 and 535–675
Interstuhl EVERYis1standard: 410–545low 380–475; high 470–600
Interstuhl JOYCEis3standard: 415–525low 395–490; high 490–620
Interstuhl PUREis3standard: 430–535low 385–445; high 450–580
Herman Miller Mirra 2standard: 406–521low 375–483; extended 425–565
Sedus se:flexstandard: 400–520Sedo-lift III: 420–530
Wilkhahn INDIN 4550 lift: 400–520ESP models 440–580; counter 650–780

Which seat height fits your body is worked out by the office chair height calculator; the guides for shorter and taller people list the chairs that reach each end.

Replacing an office chair gas lift

A seat that slowly sinks, or will not stay up, usually means a worn gas spring. EN 1335-1 requires makers to warn that only trained personnel may replace gas-spring parts. Before you buy anything, check what the chair maker covers: several name the gas lift in their guarantee.

What makers publish about gas lifts and spare parts (read 2026-11-02)
MakerGas lift or spare-part terms, as published
Steelcase (global products, incl. Leap, Gesture, Series 2)12 years on gas lifts under the Global Products Warranty; non-global products in EMEA (outside the UK and Ireland): 5 years on seating gas lifts and foam
InterstuhlThe 10-year warranty covers all spare parts, including gas springs
Wilkhahn2 years on gas lifts, castors and upholstery; 5 years on frames and mechanisms
Sedus se:flexOptional Sedo-lift III seat-height adjustment, "virtually wear-free", with a 30-year guarantee (chair: 5 years)
Flokk (HÅG, RH)Spare parts for at least 10 years from the production date
LuxySpare parts, gas lifts included, for 10 years from purchase

The spread is wide: two years on Wilkhahn's gas lifts, twelve on Steelcase's global products, and a 30-year guarantee on Sedus's optional Sedo-lift III (on the se:flex it adds €48.55 in Sedus's shop, over a standard spring that TÜV's certificate lists as Class 4). If the chair is out of warranty, ask the maker or a dealer for the original part number and give them four facts from the old spring: the marking (maker, type, class), the stroke, the overall length and the chair model. The full list of wear parts and who sells them is in repair and spare parts; how long the rest of the chair should last is in how long an office chair lasts.

DIN 4550 and EN 16955: one standard replaced the other

Older chairs and datasheets cite DIN 4550, the German standard for gas springs in office chairs. DIN EN 16955:2017-08 replaced DIN 4550:2004-12. Wilkhahn's documents for the IN and ON still name a "DIN 4550 gas lift", and ACP describes its springs as meeting EN 16955:2017, "formerly the DIN 4550 standard".

  • Committee: CEN/TC 207 "Furniture", secretariat held by UNI (Italy).
  • Approved: by CEN on 15 February 2017; the English version is dated April 2017.
  • National editions: CEN members had to publish it and withdraw conflicting national standards by October 2017. It appears as BS EN 16955:2017 in the UK, DIN EN 16955:2017-08 in Germany and SIST EN 16955:2017 in Slovenia, the same European text in each country.
  • Title: "Hardware for furniture – Tapered pressure tubes for self-supporting gas springs for the height adjustment of seating – Test methods and requirements for strength and durability".

Other standards for office chairs are summarised on the standards page.

Questions buyers ask

What does Class 4 mean on an office chair gas lift?

It is the highest strength class in EN 16955:2017. A Class 4 pressure tube survives an alternate bending moment of ±240 Nm for 2,000,000 cycles without cracks, on all 32 tubes tested, and suits seats whose load-bearing structure reaches up to 400 mm from the column's centre.

Is a Class 4 gas lift better than Class 3?

It is stronger. Class 4 is tested at ±240 Nm against ±210 Nm for Class 3, about 14% more, and allows a larger seat offset (400 mm against 370 mm). One gas-spring maker certifies its Class 3 springs for users up to 120 kg and its Class 4 springs up to 150 kg.

What length gas lift do I need?

One with the same stroke and overall length as the old one, so the seat keeps the height range the maker designed. The stroke is roughly the chair's seat-height travel: in our register it runs from 90 to 260 mm, median 115 mm. Ask the maker for the part number.

Who should replace an office chair gas lift?

EN 1335-1 requires the chair maker to warn that only trained personnel may replace gas-spring parts. Ask the maker or dealer for the part and the fitting, especially while the chair is under warranty: Steelcase covers gas lifts for 12 years on its global products, Interstuhl for 10, Wilkhahn for 2.

Sources

  1. SIST EN 16955:2017 preview: European foreword, scope, Table 1 strength classes, test procedure, test report (iTeh Standards): cdn.standards.iteh.ai/samples/39666/2d24cc2b10ce4fc2bda0b726acecb4bc/SIST-EN-16955-2017.pd
  2. iTeh Standards: SIST EN 16955:2017 catalogue entry (publication date, abstract): standards.iteh.ai/catalog/standards/sist/59235e04-3ee8-4303-bac4-69caa8ff42ea/sist-en-1695
  3. DIN Media: DIN EN 16955:2017-08, replaces DIN 4550:2004-12: www.dinmedia.de/en/standard/din-en-16955/271018041
  4. DIN: table of contents of DIN EN 16955:2017-08 (PDF): www.din.de/de/mitwirken/normenausschuesse/nhm/wdc-beuth:din21:271018041/toc-2705126/downlo
  5. ACP International: standard gas cylinders (EN 16955 Class 3 and 4, user weight): acpi.nl/en/office-chair-components/gas-cylinders/inventory-program/gas-cylinders-standard-
  6. ACP International: 2025 datasheet, standard chrome gas cylinders (PDF): acpi.nl/sites/default/files/product_download_files/2025%20acp%20cylinders%20standard%20chr
  7. Steelcase Global Products Warranty, February 2026 (PDF): www.steelcase.com/content/uploads/2026/02/2026_SC_GlobalProduct_Warranty-upd-Feb-2026.pdf
  8. Steelcase EMEA warranty 2026 (PDF): www.steelcase.com/content/uploads/sites/10/2026/10/Steelcase-EMEA-Warranty-2026_June-EN.pd
  9. Wilkhahn guarantee policy (PDF): www.wilkhahn.com/fileadmin/general/legal-docs/guarantee/Wilkhahn-Guarantee-Policy.pdf
  10. Interstuhl: EVERY product page (10-year warranty incl. gas springs): www.interstuhl.com/I/ia-en/every.php
  11. Sedus: se:flex brochure 12.2025, Sedo-lift III (PDF): www.sedus.com/download/4abca2fe48194e358ed9a1c98d4d3c41
  12. Flokk: warranties and product quality: www.flokk.com/support/warranties-and-product-quality
  13. Luxy: warranty conditions (PDF): luxy.com/wp-content/uploads/2023/04/GARANZIA.pdf

All sources checked 2 November 2026. Where a manufacturer does not publish a value, we say so rather than estimate it.

Cite this page

Best Office Chairs Europe, “Office chair gas lifts: what EN 16955 Class 3 and Class 4 mean, and how to replace one”, https://bestofficechairs.eu/standards/en-16955-gas-lift/, updated .